DiagramWiring.NET

★★★★ Wiring Diagram ★ Circuit Diagram for you



★★★★ playstation 2 controller cable connector pinout diagram

♔♔♔ The following schematic shows the PlayStation 2 Controller Cable Connector Pinout Diagram. Here is the description (click image to enlarge):

Last search terms ~~

Comments Off

★★★★ circuit diagram for electronic ballast controller of a fluorescent lamp using ir21571

♔♔♔ Electronic Ballast Controller of a Fluorescent Lamp Circuit diagram The IRPLLNR2 is a high efficiency, high power factor, fixed output electronic ballast designed for driving rapid start fluorescent lamp types. The design contains an EMI filter, active power factor correction and a ballast control circuit using the IR21571. This device features 1 x 32W T8 Lamp, 1 x 36W T8 Lamp, 90-140VAC/60Hz and 185-265VAC/50Hz input, High Power Factor/Low THD, High Frequency Operation (42kHz), Lamp Filament Preheating, Brownout Protection, Lamp Fault Protection with Auto-Restart and IR21571 HVIC Ballast Controller.

Last search terms ~~

Comments Off

★★★★ lm628 lm629 datasheet precision motion controller for motor drive interface application

♔♔♔ LM628 Precision Motion Controller Block Diagram The LM628/LM629 are dedicated motion-control processors designed for use with a variety of DC and brushless DC servo motors, and other servomechanisms which provide a quadrature incremental position feedback signal. This device features 32-bit position, velocity, and acceleration registers; programmable derivative sampling interval; velocity, target position, and filter parameters may be changed during motion, etc.

Last search terms ~~

Comments Off

★★★★ motorcycle electronic harness controller installation

♔♔♔ This manual is intended to provide a guideline for installing the Electronic Harness Controller system on your motorcycle. The Electronic Harness Controller consolidates all of the electronic functions of a motorcycle (with the exception of instrumentation and engine management) into one, easy-to-hide system.

Comments Off

★★★★ audiovox p 945 amfmmpx radio and speaker wiring

♔♔♔ Audiovox P-945 radio wiring The Audiovox P-945 is a stereo system designed for installation in cars, trucks, and vans with an existing radio opening. This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. The Audiovox P-945 features Detachable Control Panel (face), Electronically Tuned, AM, FM, MPX Radio, CD Changer Controller, CD Player, High Power 4×35 Watt Amplifier, 30 Station presets (18 FM/12 AM) with electronic memory, Back lit multi color LCD panel for display of frequency, functions and electronic control level, Multi-color power meter, Full feature CD player functions, CD changer controller, RCA low level outputs (2 channel), Aux input on 36″ lead with under dash mount, 140 Watt 4-channel amplifier (35 watts x 4).

Last search terms ~~

Comments Off

★★★★ circuit diagram for 250 w hid metal halide electronic ballast

♔♔♔ The following file is an application note from st.com describing the two stages of electronic ballast for a 250 W HID (high-intensity discharge) metal halide lamp. The ballast is composed of a boost converter (power factor controller PFC) working in fixed OFF time and an inverter composed of a full bridge that drives the lamp at low frequency square wave. The components include a PFC driver, half-bridge drivers, a microcontroller, an auxiliary power supply, a voltage reference, logic parts, an amplifier, comparators, power devices as Power MOSFETs, IGBTs, and fast diodes.

Last search terms ~~

Comments Off

★★★★ 1997 ford explorer air conditioning system circuit and schematics diagram

♔♔♔ Ford explorer AC wiring diagram The following diagram shows the 1997 Ford Explorer air conditioning system circuit and schematics. The Ford Explorer air conditioning system consists of following parts: electronic automatic temperature control module is connected to blower motor speed controller, blower motor relay, blower motor, ambient temperature sensor, in-car temperature sensor, sun load sensor, rear blower motor relay and resistor, rear air door actuator, rear integrated control panel, air conditioner clutch cycling pressure switch, A/C pressure cutoff switch, A/C compressor clutch solenoid, A/C clutch diode, powertrain control module, power distribution box and interior fuse panel.

Last search terms ~~

Leave a Comment

★★★★ db15 vga connector schematic and pinout assignment

♔♔♔ The DB15 VGA (Video Graphics Array) connector contains however 15 pins in three rows of 5 pins each. These five pins carry the color and synchronisation signals, also a digital I2C interface for two-way communication between the video controller and monitor. The common 15-pin VGA connector found on most video cards, computer monitors, high definition televisions which support VGA connections. The following schematic diagram and table shows respectively connector and pin assignment of DB15 VGA.

Last search terms ~~

Comments Off

★★★★ sony vaio pcg grs175 block and circuit diagram

♔♔♔ Sony Vaio PCG GRS175 Block and Circuit Diagram The following block and circuit diagram applies for Sony Viao PCG-GRS175. In this manual you will find detail diagram depicting interconnection between parts of the notebook (e.g. memory controller, processor, control hub, power circuit, etc). Find also frame harness diagram and exploded view of the circuit boards with parts list numbering system.

Comments Off

★★★★ xerox phaser 2135 printer wiring diagram

♔♔♔ printer-wiring-diagramThe following printer wiring diagram applies for Xerox Phaser 2135 series. Herein you will get detail illustration of the electrical schematics, and description of the wiring connection between parts e.g. wire routing at the engine controller board, bundle wires thru EMI coils, route wiring harness thru cable, route of wiring harness thru cable clamp and details of wiring passthru of the printer. Note: Ensure the wiring harness are routed inside the wiring shield except the power wiring harness; ensure the power harness inter-connect is dressed behind the flat ribbon cables to ensure it does not disconnect when the top cover is closed and make sure the wiring is not pitched by the top shield plate when it is installed.

Comments Off