DiagramWiring.NET

★★★★ Wiring Diagram ★ Circuit Diagram for you



★★★★ three phase transformers circuits diagram

♔♔♔ In the 1880’s the development of transformers contributed essentially to the enforcement of alternating and three-phase current technology. Transformers enable the transmission of electrical energy using the voltage adapted to power and distance. A three-phase transformer is made of three sets of primary and secondary windings, each set wound around one leg of an iron core assembly. A three-phase transformers must have (3) coils or windings connected in the proper sequence in order to match the incoming power.

Last search terms ~~

Comments Off

★★★★ six phase rectifier circuit diagram

♔♔♔ sixphase rectifier circuit diagramA Six-Phase rectifier is kind a transformer used to produce six alternating electromotive forces which differ in phase by one-sixth of a cycle, and which feed six diodes. When polyphase AC is rectified, the phase-shifted pulses overlap each other to produce a DC output that is much “smoother” (has less AC content) than that produced by the rectification of single-phase AC. Following schematic diagram shows sample of a Six-Phase rectifier circuit diagram.

Last search terms ~~

Comments Off

★★★★ transformer coupled ssr circuit diagram

♔♔♔ Transformer-Coupled SSR Circuit Diagram The following schematic shows the Transformer-Coupled Solid State Relay (SSR) Circuit Diagram in which the control signal is applied (through a DC-AC converter, if it is DC, or directly, if It is AC) to the primary of a small, low-power transformer, and the secondary voltage that results from the primary excitation is used (with or without rectification, amplification, or other modification) to trigger the thyristor switch.

Last search terms ~~

Comments Off

★★★★ high reactance autotransformer hid ballast circuit diagram

♔♔♔ High-Reactance Autotransformer Ballast Circuit The High-Reactance Autotransformer Ballast is used when the line voltage in insufficient to ignite the lamp using a . As a result, these ballasts are bigger, heavier, and less efficient than reactor ballasts, but they can be used in a wide variety of applications, because they come with multitap capability. It is very similar to the reactor ballast, but utilizes a two-coil design to step up the startup voltage to ignite the lamp. The coil then acts to regulate the lamp current similar to the reactor ballast. The High-Reactance Autotransformer Ballast typically has 90% + HPF power factor, and 1.4 to 1.6 current crest factor (CCF). Most HX-HPF ballasts are rated to handle supply voltage variations of 5%, which results in a 9 to 12% lamp power variation.

Last search terms ~~

Comments Off

★★★★ 3 phase synchronous motor wiring diagram

♔♔♔ 3-Phase Synchronous Motor Wiring Diagram A synchronous electric motor is an AC motor distinguished by a rotor spinning with coils passing magnets at the same rate as the alternating current and resulting magnetic field which drives it. The stepping motor is transformed into a synchronous motor by replacing the wound-wire for the AC power specification. A synchronous motor rotates at a constant speed in proportion to the AC power frequency of which current is applied directly to the wound-wire, while a stepping motor rotates in accordance with the switched phase by the driving circuit.

Last search terms ~~

Comments Off

★★★★ three phase full wave bridge rectifier circuit diagram

♔♔♔ A rectifier is an electrical device that converts alternating current (AC) to direct current (DC), a process known as rectification. This almost always involves the use of some device that only allows one-way flow of electrons, a diode. Below schematic diagram shows a Three-Phase Full Wave Bridge Rectifier Circuit Diagram. Each three-phase line connects between a pair of diodes: one to route power to the positive (+) side of the load, and the other to route power to the negative (-) side of the load.

Last search terms ~~

Comments Off

★★★★ constant wattage autotransformer cwa hid ballast circuit diagram

♔♔♔ Also known as lead style ballasts, Constant-Wattage Autotransformer (CWA) ballasts are the most common ballasts used on 175 W or higher MH lamps. It offers the best compromise between cost and performance, means of providing stabilized light output (lamp regulation) as opposed to the Magnetically Regulated circuit. It is a high power factor devise, utilizing a capacitor in series with the lamp. A ??10% line voltage variation will result in a ??5% change in lamp wattage for Mercury, or ??10%
change in wattage for Metal Halide. Below picture shows a typical Constant-Wattage Autotransformer (CWA) HID Ballast Circuit Diagram.

Last search terms ~~

Comments Off

★★★★ xerox phaser 2135 printer wiring diagram

♔♔♔ printer-wiring-diagramThe following printer wiring diagram applies for Xerox Phaser 2135 series. Herein you will get detail illustration of the electrical schematics, and description of the wiring connection between parts e.g. wire routing at the engine controller board, bundle wires thru EMI coils, route wiring harness thru cable, route of wiring harness thru cable clamp and details of wiring passthru of the printer. Note: Ensure the wiring harness are routed inside the wiring shield except the power wiring harness; ensure the power harness inter-connect is dressed behind the flat ribbon cables to ensure it does not disconnect when the top cover is closed and make sure the wiring is not pitched by the top shield plate when it is installed.

Last search terms ~~

Comments Off

★★★★ kawasaki zr550zr750 zephyr electrical wiring diagram 80 88

♔♔♔ Kawasaki ZR550 ZR750 Electrical Wiring Diagram 80 - 88 The following electrical circuit and wiring diagram applies for Kawasaki ZR550/ZR750 Zephyr (80 – 88) models. All models have a 12-volt electrical system. The components include a three-phase alternator unit and regulator/rectifier unit. The regulator maintains the charging system output within the specified range to prevent overcharging, and the rectifier converts the alternating current output to power the lights and other components and to charge the battery. The alternator rotor is mounted on the left-hand end of the crankshaft.

Last search terms ~~

Comments Off

★★★★ honda cb500f electrical wiring diagram

♔♔♔ Honda CB500F Electrical Wiring Diagram and Harness schematics The following electrical wiring diagram applies for Honda CB500F. Here you will find brief description and explanation of the electrical system and detail wiring diagram schematics of the CB500F. The electrical consists of ignition system, charging system, starting system, electrical equipments. The ignition system consists of two ignition coils, two contact breakers, four spark plugs, an ignition switch and a battery. The charging system for the CB500 is made up of the exciter field 3-phase AC generator, rectifier, voltage regulator and the fuse. The generator consists of the field coil, stator coil and the rotor; it does not contain slip rings or brushes.

Last search terms ~~

Comments Off